4140xmp manual

Unless stated otherwise, all commands and procedures apply equally to both Consoles. For clarity, only the Alpha console is shown. Referto the table of fixed word display messages found in the FUNCTIONS OFTHE CONSOLE sectionforsystem displays used with the fixed word console. Refer to the GLOSSARY at the back of this manual for,definitions ofterms used throughout. -1-2. You ve made a wise decision in choosing it, for it represents the latest in security protection technology today. Basically, this system offers you The system uses microcomputer.%ree forms of protection: burglary, technology to monitor all protection e and emergency. To realize the zones and system status and system s full potential, it is important provides appropriate information for that you feel comfortable in operating display on the Console(s) used with it. Your system consists of at least the system, and initiates appropriate one Console which provides full alarms. When programmed to do so, control of system operation, various the system can also transmit sensors which provide perimeter and appropriate alarm or status messages interior burglary protection, plus a over the phone lines to a central alarm selected nfimber of strategically monitoring station.Console display backlighting is programmable to always stay on or to light only when a key is pressed, then turn off a few minutes later. A selfhelp feature is also incorporated, which, when activated, will display abbreviated instructions for the key that has been pressed. The console also has a built-in sounder. They also feature a built-in sounder. There are two fixed word consoles available. The deluxe (41 37) is similar in style to the alpha console, while the standard (41 27) features a compact design and does not have backlit keys. -3 This code must be entered when performing most system functions, including arming and disarming of the system.

• 4140xmp manual, 4140xmp programming manual, 4140xmp user manual, 4140xmp installation manual, vista 4140xmp manual, ademco 4140xmp manual, 4140xmp t2 user manual, ademco vista 4140xmp manual, 4140xmp manual, 4140xmp manual, 4140xmp manual, ademco 4140xmp manual, 4140xmp installation manual, 4140xmp programming manual, manual for 4140xmp.

Note To The Installer.SYSTEM OVERVIEW At the time of installation, your installer programs a personal four-digit code, known only to you and yours. PLUGIN: Ademco Vista Alarm Panel with EVL3. January 12, 2015: Version 3.37 EVL3 -- fixed - obscure bug that caused the plugin to Installation - Manual: Ademco 4120xm Installation Manual View and Download ADEMCO 4160-12 C-COM installation instructions manual online. No password or user name is required to review these manuals. Ademco is the worlds largest manufacturer of security. Ask your installer ifthis has been done.This manual is a step-by-step guide that will aquaint. General Congratulations on your ownership of an Ademco Security. See your installer for your delay times. Ademco 4120xm Programming Manual. VISTA -4140XMP User's Manual L5000 - Ademco Honeywell LYNX. ADEMCO 4160-12 C-COM Installation Instructions Manual Installer. Ademco Vista 30 Installation Manual View and Download Honeywell Ademco Vista-48LA installation and setup manual online. Ademco Vista-48LA Security System pdf manual. Installation Manuals for Ademco and any other security system used by Australian Security Installers Ademco Vista 48a Installation Manual We have 1 Honeywell ADEMCO VISTA-48D manual available for free PDF download: Installation And Setup Manual. Ademco Secu rity System. You've. installer (see PANIC KEYS section).Reload to refresh your session. Reload to refresh your session. Consider upgrading your browser to Chrome, Firefox or newer versions of Internet Explorer for the best browsing experience! You may use the product manuals only for non-commercial purposes, and you may not reproduce, duplicate, copy, sell, resell or publish any portion of the product manuals without the third party owner’s prior consent. Unauthorized use strictly prohibited. The Security System can use either the Alpha Display or Fixed Word Display Consoles to perform and display system functions.

Your system provides four modes of burglary protection: STAY, AWAY INSTANT and MAXIMUM, and even allows you to BYPASS selected zones of protection while leaving the rest of the system armed. The system also provides a CHIME mode, for alerting users to the opening and closing of doors and windows while the system is disarmed. Refer to the other sections of this manual for procedures for using these features. HtLP FEAflfRE Your system is programmed by the installer with preset time delays, during which the system must be disarmed upon entering or an alarm will occur. This feature allows you to leave and reenter through the entry delay door without setting off the alarm. See ur installer for your delay times. Abbreviated user s instructions are built into the system and can be easily viewad on the alpha console s display screen. This feature will prove particularly useful if this manual is not accessible when you need to perform a seldom used system procedure with which you are not familiar. To view the abbreviated instructions, simply press and hold down the function key of interest until the description starts to appear (about 5 seconds), then release it. Refer to the FUNCTIONS OF THE CONSOLE section for detailed descriptions of each key function.Displays protection point identification and system status, messages, and user instructions. See the FIXED WORD DISPLAY CONSOLE table for Fixed Word Display messages and their meanings. 2. OFF KEY: Disarms the burglary portion of the system, silences alarms and audible trouble indicators, and clears visual alarm trouble after the problem has been corrected. 3. AWAY KEY: Completely arms both perimeter and interior burglary protection for backup protection by sensing an intruder s movements through protected interior areas as well as guarding doors, windows, etc. Late arrivals can enter through an entry delay zone without causing an alarm if the system is disarmed before the entry delay time expires. 4.

As an additional safety feature, up to 68 temporary codes can be assigned for use by those not having a need to know the master code. Temporary codes are assigned two-digit User numbers from 03 to 70. Before assigning a temporary code though, be sure it does not conflict with the DURESS code (see DURESS CODE section). Note that the master code remains in effect even when a temporary code is assigned. NOTE: Users to whom temporary wales have been assigned should not be shown how to bypass protection points unless they have a need to know. It is also recommended that obvious codes such as 1111 or 1234 not be assianed. The security code is always required when disarming the system. HIGH SECURITY FEATURE The system can be programmed to require a 6-digit code for arming and disarming. The 6-digit code consists of the 2-digit user number plus a 4- digit code. Ask your installer if this option is programmed for your system. To delete a code, enter Master Code for that User Number. 5. The Console will beep once when procedure has been completed successfully.These numbers will appear on the display, along with an alpha descriptor for that zone (if programmed), when the respect ive zone is faulted. The fire protection portion of your security system (if used) is always on and will sound an alarm if a fire condition is detected. Refer to the FIRE ALARM SYSTEM section for important information concerning fire protection, smoke detectors and planning emergency exit routes from your house. The burglary protection portion of your system must be armed before it will sense burglary alarm conditions. When an alarm occurs, both the console and external sounders will sound, and a message in the Display Window will identify the zone(s) causing the alarm. In addition, if your system is connected to a central monitoring station, an alarm report will be sent. Disarming the system will stop alarm sounding.

CHIME Appears when the CHIME feature is activated. BAT Low battery condition in a Radio Transmitter (if used). LARM Appears when an intrusion has been detected and the system is armed (also appears during a Fire alarm). Accompanied by the protection zone ID in alarm. Accompanied by a display of zone number in trouble. FIRE Appears when a fire alarm is present. Accompanied by a display of the zone in alarm.The abbreviated instructions for the READY key will appear first, followed by the descriptors programmed for your system. Displaying all descricdors is useful when vou need when all protection zones have to kn ow the zone num6er of a been either closed or bypassed.Bear this in mind whenever the instructions for the Alpha Console indicate that the DISARMED or READY message will be displayed -8- The Bypass message will be displayed indicating the presence of one or more bypassd zones. NOTE All bypasses are removed when an OFF sequence (security.Arm the system as usual. 2. Wait for afl bypassed zones to be Bypassed zones are unprotected sequentiafty displayed.LIMITATIONS. Fire or emergency zones cannot be bypassed. Arming the system before bypassed zones are displayed nulfiies all bypasses. -9- Late arrivals can enter through the entry delay zone door and disarm the system within the entry delay period without causing an alarm. See your installer for actual delay times set for your system. Alarms will occur instantly when any exterior protection point is violated, except the entry delay zone door, which will activate an alarm if the system is not disarmed within the entry delay period. Interior protection points are disarmed to permit freedom of movement throughout the interior. INSTANT KEY RESULT Arms sensors guarding doors and windows, with entry delay off. Alarr - will occur instantly when any exte protection point is violated, includiw the entry delay zone door. Interior protection points are disarmed to permit freedom of movement throughout the interior.

STAY KEY: Arms the perimeter burglary protection, guarding doors, windows and other perimeter protection points, and sounds an alarm if one is opened. Interior protection is not armed, which allows movement within your house without causing an alarm. Late arrivals can enter through an entry delay zone without causing an alarm if the system is disarmed before the entry delay time expires. 5. TEST KEY: Tests the system and alarm sounder if disarmed. Refer to the TESTING THE SYSTEM section for test procedures. 6. BYPASS KEY: Removes individual protection zones from being monitored by the system. This key is also used to display all zone descriptors that have been programmed for your system, by holding the key down for at least 5 seconds. 12. INSTANT KEY: Arms in manner similar to STAY mode, but turns off the entry delay period, offering greater security while inside and not expecting any late arrivals. An alarm will occur immediately upon opening any perimeter protection point, including entty delay zones. 13. MAXIMUM KEY: Arms in manner similar to AWAY mode, but eliminates the entry delay period, thus providing maximum protection. An alarm will occur immediately upon opening any protection point, including entry delay zones. 14. POWER INDICATOR: (GREEN) Lit when primary power is on. If off, system is operating on it backup battery power. CALL YOU- INSTALLER IMMEDIATELY. 15. ARMED INDICATOR: (RED) Lit when the system has been armed (STAY, AWAY, INSTANT or MAXIMUM). 16. INTERNAL SOUNDER: Source of audible internal warning and confirmation sounds, as well as alarms (see Summary of Audible Notifications ). INSTANT Perimeter burglary zcmes armed and entry delay is turned off. BYPASS One or more burglary p rotection zones have been bypassed. NOT READY Appears when burglary porlion of the system is not ready for arming (due to open protection zones). READY The burglary POrtion of the system is ready to be armed. NO AC Appears when AC power has been cutoff.

The audible warning sound for CHECK or LO BAT conditions may be silenced by pressing any key. TYPICAL ALPHA CONSOLE CHECK DISPLAYS 1. A display of C H E C K 4. A display accompanied by a display of CALL SERVICE indicates that a problem exists with the system that eliminates some of the protection. First, determine if the zone(s) displayed are intact and make them so if they are not. If the problem has been corrected, the display of the zone descriptor(s) and CHECK should disappear. If not, key an OFF sequence (Code plus OFF) to clear the display. If the display persists, CALL FOR SERVICE IMMEDIATELY. 3. A display of COMM. FAILURE at the Console indicates that a failure has occurred in the telephone communication portion of your system.If only some lights are out on the premises, check circuit breakers and fuses and reset or replace as necessary. CALL FOR SERVICE IMMEDIATELY if AC power cannot be restored. Not all systems use wireless transmitters. Note that zone numbers represent problems with wireless receivers, which are not user serviceable.Arranging some kind of regular program with him is advisable. Your local service representative is: I I -16 I I An interrupted sound will - o be produced by optional exterior sounders. A FIRE message will appear at Jr Console and remain on until you silence the alarm. The zone descriptor of the zone(s) in an alarm condition will be displayed at the Console. Note: Approval of the panel s burglar alarm functions does not fall within the (California) State Fire Marshal s area of jurisdiction. SILENCING A FIRE ALARM: 1. Silence the alarm by entering your code and pressing the OFF key. Be sure to check that smoke detectors are not responding to smoke or heat producing objects in their vicinity. Should this be the case, eliminate the source of heat or smoke. 3. If this does not remedy the problem, there may still be smoke in the detector. Clear it by fanning the detector for about 30 seconds. 4.

When the problem has been corrected, clear the display by entering your code and pressing the OFF key. 17- In addition, it is recommended that the householder consider the use of heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages. MAXIMUM FLOOR COvERAGE DETECTORS AT TOP OF STAIRWELLS. 15i?3 BEDRcOM Blmfmcw o o samijc44-18- The following steps are recommended by the National Fire Protection Association: 1. Plan on your detector or your. One path of escape should lead to the door that permits normal exit from the building. The other may be a window, should your path be unpassable. Station an escape ladder at such windows if there is a long drop to the ground. Sketch a floor plan of the building, Show windows, doors, stairs and rooftops that can be used to escape. Indicate escape routes for each room. Keep these routes free from obstruction and post copies of the escape routes in every room Assure that all bedroom doors are shut while you are asleep. This will prevent deadly smoke from entering while you bscape. Try the door. If the door is hot, check your alternate escape route. If the door is cool, open it cautiously. Be prepared to slam the door if smoke or heat rushes in. Crawl in the smoke and hold your breath. Escape quickly; don t panic. 8. Establish a common meeting place outdoors, away from your house, where everyone can meet and then take steps to contact the authorities and account for those missing. Choose someone to assure that nobody returns to the house many die going back.Subsequently, the following is displayed: DISARMED BYPASS Ready to Arm Opened Zone identltications will appear. LO BAT displayed with description of transmitter. ARMED AWAY or ARMED MAXIMUM is displayed.ARMED Light is on when armed; off when disarmed; flashes to indicate a previous Detection Systems, Inc.

lo Compfete system protection is in effect immediately.AWAY KEY RESULT Arms all perimeter and interior sensors,with entry delay on. See your instaear for actual detay times set for your system. MAXIMUM KEY RESULT Arms all perimeter and interior sensors, with entry delay off. The Ready message will be displayed and the console will beep once to confirm that the system is disarmed, unless an alarm has occurred. 2. If an alarm has occurred, note the zone descriptor displayed and repeat step 1 to restore the Ready RESULT Any alarm sounders will be silenced ALARM and zone descriptor displayed) will clear only when thy open sensor is closed. A fire alarm is indicated by a display of both FIRE and the zone descriptor on the Console. These will clear only when the fire zone is again intact.Increase the final digit by one and then press OFF (or AWAY, etc.The system will disarm (or arm), but can silently notify the central station of your situation, if that service has been provided. For example, if the Normal security code is, the Duress security code is UNDER IMPORTANT THREAT) This code is useful only when connected to a central station. Duress code capability is not present for codes ending in 9. Users of temporary codes must be instructed to enter their codes carefully to avoid the possibility of accidentally entering the Duress code. Note that Chime mode can be activated only when the system is Disarmed.The CHIME MODE ON message will appear for about two seconds then disappear. To display this message again (to determine whether chime mode is on or off), simply press and hold down the CHIME key for 5 seconds. The CHIME MODE OFF message will appear for about two seconds then disappear. The message or installer. When a message is could take up to four screens to waiting to be viewed, the message display ail the information available.See your installer for the functions that have been programmed for these en rewrmy key pairs.

Typical functions that might be programmed are Silent Police, Audible Police, Personal Emergency, and Fire. To use a Panic function, simply press both keys of the assigned pair at the same time and hold down for at least two seconds. If programmed for audible emergency by your installer, a loud, steady alarm will sound at your console and at any external sounders that may be connected (ALARM plus a description would also be displayed). A personal emergency alarm will notify the central station (if connected) and will sound at Consoles, but not at external bells or sirens. A fire alarm will send a fire alarm message to the central station and will uniquely sound external bells and sirens (FIRE plus a description would also be displayed). 14-. The external sounder should sound for 3 seconds and then turn off. If the sounder does not sound, it may be due to dialer communication activity. Wait a few minutes and try again.Immediately after the sounder turns off, the system enters Test mode, which allows each protection point to be checked for proper operation. The Console will sound a single beep at 15 second intervals (if no protection points are violated), to indicate that it is in Test mode. Open and close each protected door and window in turn. Each action should produce three beeps from the Console, and the identification of each protection point should appear on the dispfay Walk in front of any interior motion detectors (if used). Listen for three beeps as the detector senses movement. Follow the manufacturer s instructions to test all smoke detectors to ensure that all are operational and functioning properly. The identifiiion of each detector shoutd appear when it is activated. When all protection points have been checked, there should be no zone identification numbers displayed. If a problem is experienced with any protection point (no confirming beeps, no display), CALL FOR SERVICE IMMEDIATELY.

, 130 Perinton Parkway, Fairport, This certification means that the equipment Security System User's Guide Some terms widely used within Read this manual carefully and become familiar The system can be programmed to communicate with a central monitoring station FCC Part 15 Class With PC5OORK Keypad. 1996, 2002 Digital Security Controls Ltd. Toronto, Canada Printed in Canada 29000534 R3 Toronto, Canada Printed in Canada 29000534 R3 PC55O With PC5OORK Keypad Industry Canada Notice NOTICE: The Industry Canada label identifies The DESTINY has been designed to provide you with a maximum level of security The entire manual should Owner s Manual Safety Procedures. Safety Planning. Fire Protection. System Operation. Sensors. Wireless System Keypad (Wireless Remote Transmitter). It is thus very important that a family escape plan be developed and rehearsed. 1. Every PIMA Electronic Systems Ltd. www.pima-alarms.com FCC Notice These limits are designed to provide General System Operation Read this manual carefully and have your installer The entire manual should be carefully The entire Paul, MN 55109 FCC Notices FCC Part 15 Information to the User Changes or modifications not expressly approved S1632 IMPORTANT! PROPER INTRUSION PROTECTION For proper intrusion coverage, sensors should The alarm panel is capable of extensive Some terms widely used within the industry are these: Arm and Disarm Your To use this website, you must agree to our Privacy Policy, including cookie policy.